Cisco CX-FEIP-2TX= Installation and con?guration Dokumentacja Strona 278
- Strona / 493
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
7-22
Cisco ONS 15454 Installation and Operations Guide, R3.2
March 2002
Chapter 7 Card Provisioning
Provisioning Optical Cards
NPJC-Pdet
Negative Pointer Justification
Count, STS Path detected. See the
“Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (Near and Far End):
Line
• 0 (15 minutes)
• 0 (1 day)
PPJC-Pgen
Positive Pointer Justification
Count, STS Path generated. See
the “Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (Near and Far End)
NPJC-Pgen
Negative Pointer Justification
Count, STS Path generated. See
the “Enabling Pointer Justification
Count Parameters” section on
page 8-12 for more information.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (Near and Far End)
PSC
Protection Switching Count (Line) Numeric. Defaults (15 min/1 day):
Line
• 1/5 (Near End)
• 0/0 (Far End)
PSD
Protection Switch Duration (Line) Numeric. Defaults (15 min/1 day):
Line
• 300/600 (Near End)
• 0/0 (all OC-N cards, Far End)
PSC-W
Protection Switching Count -
Working line
BLSR is not supported on the
OC-3 card; therefore, the PSC-W,
PSC-S, and PSC-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
PSD-W
Protection Switching Duration -
Working line
BLSR is not supported on the
OC-3 card; therefore, the PSD-W,
PSD-S, and PSD-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
PSC-S
Protection Switching Duration -
Span
BLSR is not supported on the
OC-3 card; therefore, the PSC-W,
PSC-S, and PSC-R PMs do not
increment.
Numeric. Defaults (15 min/1 day):
Line
• 0/0 (all OC-N cards except OC-3, Near and
Far End)
Table 7-8 OC-N Card Threshold Settings on the Provisioning > Thresholds Tab (continued)
Heading Description Options
- Operations Guide 1
- CONTENTS 3
- Contents 10
- March 2002 10
- Hardware Installation 29
- Ethernet Operation 32
- Procedures 33
- About This Manual 35
- Related Documentation 36
- Conventions 37
- Obtaining Documentation 37
- World Wide Web 38
- Ordering Documentation 38
- Documentation Feedback 38
- Cisco.com 39
- Technical Assistance Center 39
- Cisco TAC Escalation Center 39
- 1.1 Installation Overview 42
- 1.2 Installation Equipment 43
- 1.2.1 Included Materials 44
- 1.3 Rack Installation 45
- Rack Installation 46
- 1.3.2 Mounting a Single Node 47
- Equipment rack 48
- Universal 48
- (reversible) 48
- 1.4 Front Door Access 51
- Front Door Access 52
- Open the door 53
- 1.5 Backplane Access 54
- 1.5.1 Lower Backplane Cover 55
- 1.5.2 Alarm Interface Panel 56
- 1.6 EIA Installation 57
- 1.6.2 High-Density BNC EIA 58
- 1.6.3 SMB EIA 59
- 1.6.4 AMP Champ EIA 60
- AMP CHAMP 61
- EIA Installation 62
- Fan-tray 67
- Power and Ground Installation 68
- FRAME GROUND 69
- Battery leads (red) 70
- Return leads (black) 70
- 1.9.1 Alarm Installation 72
- 1.9.2 Timing Installation 73
- 1.9.3 LAN Installation 74
- Coaxial Cable Installation 76
- DS-1 Cable Installation 79
- DS-1 Electrical Interface 81
- Adapter or balun 81
- Binder Group) (continued) 82
- 1.12 Card Installation 84
- 1.12.1 Slot Requirements 85
- Card Installation 86
- Cable Routing and Management 94
- Reversible jumper 95
- Fold down 95
- FAN FAIL 97
- Connector ends 98
- Tie-wrap 98
- Tie-wraps 98
- Screw locations 100
- 1.15 Ferrite Installation 101
- 1730-0730 for each cable 102
- January 2005 103
- Ferrite Installation 103
- 1.16.2 Slot Assignments 104
- 1.16.3 Cards 104
- 1.16.1 Bandwidth 104
- 1.16.4 Configurations 105
- 1.17 Installation Checklist 107
- Software Installation 111
- 2.2 Computer Requirements 112
- Computer Requirements 113
- Running the CTC Setup Wizard 114
- 2.4.2 Network Connections 117
- Logging into the ONS 15454 119
- Login node 120
- Login node group 120
- Step 5 Click OK 122
- 2.6.1 Node View 124
- 2.6.1.3 Node View Tabs 125
- 2.6.2 Network View 126
- 2.6.2.2 Network View Tasks 127
- 2.6.2.3 Creating Domains 128
- Table 2-8 Managing Domains 129
- Working with the CTC Window 130
- 2.6.3 Card View 132
- 2.7 CTC Navigation 133
- Moving the mouse 134
- ONS 15454 134
- 2.8 Viewing CTC Table Data 135
- Viewing CTC Table Data 136
- OC-N Cards 137
- DS-N Cards 137
- Procedure: Export CTC Data 139
- Node Setup 141
- Chapter 3 Node Setup 142
- Procedure: Create New Users 148
- Procedure: Edit a User 148
- Procedure: Delete a User 148
- Creating Protection Groups 149
- Procedure: Enable Ports 150
- Setting Up ONS 15454 Timing 152
- Viewing ONS 15454 Inventory 157
- Viewing CTC Software Versions 159
- IP Networking 161
- Chapter 4 IP Networking 162
- 15454s #2 and #3 164
- Procedure: Set up OSPF 172
- SONET Topologies 179
- 5.2.1 Two-Fiber BLSRs 180
- 5.2.2 Four-Fiber BLSRs 182
- 5.2.3 K3 Byte Remapping 185
- 5.2.4 BLSR Bandwidth 185
- Figure 5-9 A five-node BLSR 187
- Free Slot 188
- 5.2.6 Setting Up BLSRs 189
- Procedure: Remap the K3 Byte 192
- Procedure: Provision the BLSR 193
- Procedure: Add a BLSR Node 197
- Procedure: Remove a BLSR Node 200
- Figure 5-23 An OC-3 UPSR 207
- 5.3.2 Setting Up a UPSR 209
- Procedure: Add a UPSR Node 213
- 5.4 Subtending Rings 215
- 13 serve the UPSR 216
- Subtending Rings 217
- Linear ADM Configurations 220
- Path-Protected Mesh Networks 229
- Working traffic 230
- Circuits and Tunnels 233
- Creating Monitor Circuits 241
- 6.5 Searching for Circuits 242
- 6.6 Editing UPSR Circuits 242
- Editing UPSR Circuits 243
- 6.7 Creating a Path Trace 244
- Creating a Path Trace 245
- Cross-Connect Card Capacities 247
- 6.8.1 VT1.5 Cross-Connects 248
- 6.8.2 VT Tunnels 251
- 6.9 Creating DCC Tunnels 253
- Creating DCC Tunnels 254
- Card Provisioning 257
- Provisioning Electrical Cards 258
- 7.2.1 DS-1 Card Parameters 259
- 7.2.2 DS-3 Card Parameters 262
- 7.2.3 DS3E Card Parameters 264
- 7.2.5 EC1-12 Card Parameters 270
- Provisioning Optical Cards 274
- 7.4 Provisioning IPPM 280
- Provisioning IPPM 281
- 7.5.1 Using Virtual Wires 282
- Step 5 Click Apply 286
- Performance Monitoring 291
- 8.1.1 Viewing PMs 292
- Near End and Far End buttons 295
- Signal-type menus 296
- Baseline button 297
- 8.1.6 Using the Clear Button 298
- 8.2 Changing Thresholds 299
- STS FC-P 316
- STS SES-P 316
- STS UAS-P 316
- 9.1.1 G1000-4 Application 342
- G1000-4 Card 343
- 9.1.5 G1000-4 LEDs 345
- FAIL LED 346
- ACT/LINK LED 346
- 9.2 E Series Cards 349
- 9.2.1 E100T-12/E100T-G Card 350
- 9.2.2 E1000-2/E1000-2-G Card 350
- 9.2.3 E Series LEDs 350
- E Series Cards 351
- Table 9-4 Available GBICs 352
- 6. STS 3c +STS 3c + 6 STS-1s 354
- 7. 12 STS-1s 354
- Figure 9-17 Viewing a span 362
- Step 31 Click Finish 362
- ONS NodeONS Node 365
- SONET/SDH 365
- Ethernet 365
- Point-to-Point Circuit 371
- ONS Node ONS Node 371
- 9.6 E Series VLAN Support 376
- Data Flow 377
- E Series VLAN Support 379
- Redundant path (blocked) 380
- Primary path (forwarding) 380
- Step 4 Click Apply 381
- 9.8.1.1 Statistics Window 383
- 9.8.1.2 Utilization Window 385
- 9.8.1.4 History Window 386
- 9.8.3.1 Statistics Window 387
- 9.8.3.4 History Window 388
- 9.8.4.1 MAC Table Window 389
- 10.1 Overview 395
- Viewing ONS 15454 Alarms 396
- Table 10-3 Alarm Display 397
- 10.2.3 Conditions Tab 399
- 10.2.4 Viewing History 401
- 10.3 Alarm Profiles 402
- Alarm Profiles 403
- 10.3.1.1 Alarm Profile Menus 404
- 10.3.1.4 Row Display Options 405
- 10.4 Suppressing Alarms 408
- Suppressing Alarms 409
- 11.1 SNMP Overview 411
- 11.2 SNMP Basic Components 412
- 11.3 SNMP Support 413
- Chapter 11 SNMP 414
- SNMP Support 414
- Table 11-1 SNMP Message Types 415
- 11.5 SNMP Traps 416
- SNMP Traps 417
- 11.6 SNMP Community Names 419
- 11.7.4 Alarm Group 420
- 11.7.5 Event Group 420
- Circuit Routing 421
- Secondary Sources and Drops 422
- Manual Circuit Routing 423
- Regulatory Compliance 429
- Japan Approvals 430
- Korea Approvals 432
- Installation Warnings 433
- DC Power Connection Warning 435
- Class 1 Laser Product Warning 438
- Restricted Area Warning 439
- Ground Connection Warning 440
- Qualified Personnel Warning 441
- More Than One Power Supply 442
- Unterminated Fiber Warning 443
- Laser Activation Warning 445
- Numerics 447
- Acronyms 448
- Glossary 462
Powiązane produkty i podręczniki dla Networking Cisco CX-FEIP-2TX= Installation and con?guration
Networking Cisco 1710 Informacje Techniczne
(26 strony)
(26 strony)
Networking Cisco MC16E Dokumentacja
(19 strony)
(19 strony)
Networking Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Instrukcja Użytkownika
(398 strony)
(398 strony)
Networking Cisco 678 Dokumentacja
(192 strony)
(192 strony)
Networking Cisco PIX-515E Przewodnik Instalacji
(20 strony)
(20 strony)
Networking Cisco WRT300N Podręcznik Użytkownika
(90 strony)
(90 strony)
Networking Cisco 15216 EDFA2 Dokumentacja
(280 strony)
(280 strony)
Networking Cisco uBR10-LCP2-MC28C Dokumentacja
(32 strony)
(32 strony)
Networking Cisco 4430 Instrukcja Użytkownika
(12 strony)
(12 strony)
Networking Cisco MGX 8230 Dokumentacja
(282 strony)
(282 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji