
673
Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8
OL-10394-05 Rev. R0
Symptoms: A router may crash when the clear ip /jointfilesconvert/422273/bgp command is entered.
Conditions: Occurs on devices running BGP and configured as a route reflector client with
conditional route injection configured.
Workaround: Unconfigure conditional route injection.
• CSCsk28748
Symptom: When an IMA group subinterface (atm1/ima1.14016) is configured before a no shutis
done on the IMA group interface, the maximum value VBR-NRT peak cell rate (PCR) option is
displayed as 1536/1920(T1/E1) instead of 1523/1904.
Conditions: Occurred when IMA group subinterface is configured before assigning ATM interface
to the IMA group.
Workaround: Configure the IMA group interface first and then configure image group sub- interface.
• CSCsk48366
Symptoms: The following traceback occurs following a stateful switchover (SSO).
CWAN_SPA-3-POWER_CYCLE: Configuration mismatch occurred on Shared Port Adapter 2/0
Conditions: Occurred on a Cisco 7600 router running Cisco IOS Release 12.2SRB image with
8T1E1-SPA.
Workaround: There is no workaround.
• CSCsl00472
Symptoms: A Cisco router unexpectedly reloads with memory corruption after showing multiple
"%SYS-2-INPUT_GETBUF: Bad getbuffer" messages
Conditions: Occurs during normal operation.
Workaround: There is no workaround.
• CSCsm28287
Symptoms: After shutting down a GRE tunnel interface, the active RP crashed and switchover took
place. The following error message was displayed:
%ALIGN-1-FATAL: Illegal access to a low address 13:02:45 UTC Fri Jan 18 2008 addr=0xD,
pc=0x7144A5A0, ra=0x7209FFF8, sp=0x5ABEE90 SLOT0:01:40:03: %DUMPER-3-PROCINFO: pid =
16409: (sbin/ios-base), terminated due to signal SIGBUS, Bus error (Invalid address
alignment) SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: zero at v0 v1
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: R0 00000000 7A5FD854 EF4321F9
7A6452D0 SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: a0 a1 a2 a3 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R4 EF4321CD 0000000B 0000000B 00000000
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: t0 t1 t2 t3 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R8 7CB96E10 00FDDBE0 00000000 EFFFFFFF
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: t4 t5 t6 t7 SLOT0:01:40:03:
%DUMPER-3-REGISTERS_INFO: 16409: R12 00000000 F7E8E12F 00000000 00000000
SLOT0:01:40:03: %DUMPER-3-REGISTERS_INFO: 16409: s0
Conditions: Occurred on a Cisco 7200 running an internal build of Cisco IOS Release 12.2SX.
Workaround: There is no workaround.
• CSCsm55817
Symptoms: When configuring ATM PVCs, under the PVC syntax you can provide a handle to
describe the PVC. If this handle starts with "00" (zero zero) then the command will fail.
Conditions: The symptom is observed when configuring ATM PVCs and where the PVC handle
starts with "00".
Workaround: Do not use handles that start with "00".
Komentarze do niniejszej Instrukcji