Cisco SCE8000 Dokumentacja Strona 375
- Strona / 778
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2-335
Cisco SCE 8000 CLI Command Reference
Chapter 2 CLI Command Reference
rdr-formatter protocol
rdr-formatter protocol
Configures the RDR formatter protocol.
rdr-formatter protocol rdrv1 | NetflowV9
Syntax Description
Command Default The default is rdrv1.
Command Modes Global configuration
Command History This table includes the following release-specific history entries:
Usage Guidelines The RDR formatter protocol can be configured only when the RDR-formatter service is disabled (Use
the no service rdr-formatter command ).
This command configures the protocol to be used globally by the RDR formatter. A protocol can also be
assigned specifically to each RDR formatter destination (see the rdr-formatter destination command).
Authorization: admin
Examples The following example illustrates how to reset the RDR formatter.
SCE8000> enable 15
Password: <cisco>
SCE8000#> configure
SCE8000(config)# no service rdr-formatter
SCE8000(config)# rdr-formatter protocol rdrv1
SCE8000(config)# service rdr-formatter
SCE8000(config)#>
Related Commands
rdrv1 | NetflowV9 Name of the RDR formatter protocol.
Release Modification
3.0.0 This command was introduced.
Command Description
show rdr-formatter protocol Displays the RDR-formatter protocol used.
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 10
- About This Guide 19
- Document Revision History 20
- Organization 20
- Related Publications 20
- Conventions 21
- Command-Line Interface 23
- CLI Authorization Levels 24
- CLI Command Mode Hierarchy 25
- • E1: interface Linecard 0 27
- • E3: (traffic ports) 27
- Prompt Indications 28
- Example: 29
- CLI Help Features 31
- Argument Help 32
- Command History 34
- Keyboard Shortcuts 34
- Auto-Completion 35
- FTP User Name and Password 36
- Managing Command Output 37
- Creating a CLI Script 39
- CLI Command Reference 41
- • 0 (user) 43
- • 5 (viewer) 43
- • 10 (admin) 43
- • 15 (root) 43
- • none—Use no authentication 48
- EXAMPLE 1 54
- EXAMPLE 2 54
- • Permit/deny field 56
- • attack-detector 62
- • access-list 62
- • Action—report 63
- command to disable it 95
- is 60 minutes 123
- General Guidelines 124
- Recurring Configurations 124
- Specifying Explicit Days 125
- Example 1 125
- Example 2 125
- Example 3 125
- • /system/preconf 143
- • /system/prevconf 144
- Disable multi-mapping: 163
- Load Balancing 176
- High Availability (Failover) 176
- Figure 2-1 Disable Command 181
- • full—Full duplex 183
- • half—Half duplex 183
- Figure 2-2 Enable Command 185
- • Must begin with a letter 186
- • Cannot contain spaces 186
- • Are case-sensitive 186
- • General configuration files 190
- • Static party DB files 190
- • start—Starts recording 195
- • stop—Stops recording 195
- Command Description 206
- EXEC authorization level 214
- • global-controller bandwidth 222
- • global-controller name 222
- EXAMPLE 1: 249
- EXAMPLE 2: 249
- Ipv6-IANA 271
- • warning 292
- • Adding an entry 297
- • Removing an entry 297
- • traffic-engineering skip 327
- • vpn skip 327
- • END_USER_E164 343
- • END_USER_IMSI 343
- • END_USER_NAI 343
- • END_USER_SIP-URI 343
- • END_USER_PRIVATE 343
- • Link Usage RDRs (LURs) 353
- • Package Usage RDRs (PURs) 353
- • Category 1—40 MB 364
- • Category 2—24 MB 364
- • Category 3—8 MB 364
- • Category 4—8 MB 364
- Priorities 369
- Table 2-8 Valid Mode Settings 373
- • The host ends with .com 384
- User Authorization Guidelines 390
- • Calling station ID 401
- • NAS port 401
- • Username 401
- • CDP mode 422
- Counter Definitions 514
- Current values: 514
- Peak values: 514
- Event counters: 515
- • Has no mapping 517
- Examples Example 1 521
- Example 4 522
- TP-IP-range 533
- EXAMPLE 3 542
- EXAMPLE 4 542
- • duplex 550
- • IP address 550
- • auto-fail-over 550
- • Quota rate control 574
- • Maximum size of the buffer 574
- SCE8000> 597
- • Main connection 602
- SCE8000(config)#> 678
- • SNMP traps 683
- • Enterprise traps 683
- Authorization: admin 686
- Examples 686
- IP specification 740
- Port specification 741
- Tunnel ID specification 741
- Traffic counter name 741
- • Action = flow-capture 743
- IP Specification 744
- Limitations 747
- • Link-0 757
- • Link-1 757
- • VAS server is enabled 759
- • Server has a VLAN tag 759
- • Server Group ID 764
- • SCE 8000: 0-63 764
- Direction 771
- PIR Values 772
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji