Cisco Cisco Aironet Wireless LAN Client Dokumentacja Strona 79
- Strona / 142
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
5-17
Cisco Aironet Wireless LAN Client Adapters Installation and Configuration Guide for Linux
OL-1376-02
Chapter 5 Advanced Configuration
Overview
Table 5-6 lists and describes the client adapter’s advanced infrastructure parameters. Follow the
instructions in the table to initially set or to change any parameters.
Table 5-6 Advanced (Infrastructure) Parameters
Parameter Description
Antenna Mode (Receive) Specifies the antenna that your client adapter uses to receive data:
• PC card—The PC card’s integrated, permanently attached
antenna operates best when used in diversity mode. Diversity
mode allows the card to use the better signal from its two antenna
ports.
Range: Diversity (Both), Right Antenna Only, Left Antenna Only
Default: Diversity (Both)
• LM card – The LM card is shipped without an antenna; however,
an antenna can be connected through the card’s external
connector. If a snap-on antenna is used, we recommend diversity
mode. Otherwise, select the mode that corresponds to the antenna
port to which the antenna is connected.
Range: Diversity (Both), Right Antenna Only, Left Antenna Only
Default: Diversity (Both)
• PCI client adapter—The PCI client adapter must use the Right
Antenna Only option
Default: Right Antenna Only
Antenna Mode (Transmit) Specifies the antenna that your client adapter uses to transmit data.
See the Antenna Mode (Receive) parameter above for information on
the options available for your client adapter.
Specified Access Point 1- 4 Specifies the MAC addresses of up to four preferred access points
with which you want to associate. If the specified access points are not
found or you roam out of range, you might associate to another access
point.
You can enter the MAC addresses of the access points in the edit boxes
or choose not to specify access points by leaving the boxes blank.
Default: No access points specified
Note This parameter should be used only for access points that are
in repeater mode. For normal operation, leave these fields
blank because specifying an access point slows down the
roaming process.
- Guide for Linux 1
- CONTENTS 3
- Contents 4
- 5 Advanced Configuration 5-1 5
- 6 Diagnostics 6-1 5
- 7 Routine Procedures 7-1 5
- 8 Troubleshooting 8-1 6
- Japanese Translation D-7 7
- English Translation D-7 7
- Audience 10
- Organization 10
- Conventions 11
- Attention 12
- Avvertenza 12
- Advarsel 12
- Related Publications 13
- Obtaining Documentation 13
- Ordering Documentation 14
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Cisco TAC Escalation Center 16
- Overview 17
- Terminology 18
- Parts of the Client Adapter 19
- Chapter 1 Overview 20
- Ad Hoc Wireless LAN 21
- Site Survey 22
- Preparing for Installation 25
- Safety Information 26
- Unpacking the Client Adapter 27
- System Requirements 27
- Site Requirements 28
- PCMCIA Installation 32
- Enter (Figure 3-3) 33
- Figure 3-7 Make All Screen 37
- Option 1 for Red Hat Systems 38
- Option 2 for Red Hat Systems 39
- Verifying Installation 41
- Inserting a PC Card 42
- Additional Procedures 44
- Opening the Client Utilities 46
- Selecting the Radio 47
- Enabling LEAP 52
- Using the Bcard Utility 53
- Finishing the Installation 54
- Enabling Security Features 55
- Server-Based Authentication 56
- Getting Started 56
- Changing the Password 56
- Entering a New WEP Key 57
- Selecting an Existing WEP Key 59
- Enabling WEP 59
- Message Integrity Check (MIC) 60
- Advanced Configuration 63
- Setting Enterprise Parameters 65
- Table 5-2 System Parameters 66
- Network Type Description 67
- Authentication Description 69
- Setting RF Network Parameters 71
- Data Rate Description 72
- Diagnostics 83
- Chapter 6 Diagnostics 85
- Receive Statistics 90
- Transmit Statistics 91
- Routine Procedures 93
- Ascertaining the ACU Version 94
- Selecting a Help Browser 95
- Loading New Firmware 95
- Uninstalling Manually 97
- Removing a PC Card 99
- Removing a PCI Client Adapter 99
- OL-1376-02 100
- Removing the Client Adapter 100
- Troubleshooting 101
- Using the Indicator LEDs 102
- Getting Help 104
- (Figure 8-3) 105
- Technical Specifications 107
- Power output 109
- Receiver sensitivity 109
- APPENDIX 113
- Channel Sets 114
- Translated Safety Warnings 117
- Warning for Laptop Users 119
- ¡Advertencia! 120
- Varning! 120
- Information 121
- Tested To Comply 122
- With FCC Standards 122
- FOR HOME OR OFFICE USE 122
- Canadian Compliance Statement 123
- Liechtenstein 124
- Japanese Translation 127
- English Translation 127
- GLOSSARY 129
- Glossary 130
- OL-1367-02 130
Powiązane produkty i podręczniki dla Networking Cisco Cisco Aironet Wireless LAN Client
Networking Cisco AVS 3120 Podręcznik Użytkownika
(14 strony)
(14 strony)
Networking Cisco SN 5428-2 Przewodnik Instalacji
(16 strony)
(16 strony)
Networking Cisco SE2800 Instrukcja Użytkownika
(22 strony)
(22 strony)
Networking Cisco MWR-1900-27 Dokumentacja
(448 strony)
(448 strony)
(4 strony)
Networking Cisco 7513 Dokumentacja
(24 strony)
(24 strony)
Networking Cisco 7576 Instrukcja Użytkownika
(44 strony)
(44 strony)
Networking Cisco Engine 611 Dokumentacja
(516 strony)
(516 strony)
(126 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji