Cisco 7576 Instrukcja Użytkownika

INSTALL THE HARDWARECONNECT THE RSPSTART AND CONFIGURE THE SYSTEMINSTALL FIELD REPLACEABLE UNITS (FRUS)1234Quick Start GuideIsCiscodocumentationhelpfu

8Mount the Chassis in the RackInstall the Hardware53487POWERAPOWERBCaution Two people are required toperform this step.Step 1 With a person positioned

9Install Interface Processors, Fillers, VIPs, or RSPsInstall the HardwareTheRouteSwitch Processor (RSP) comes uninstalledwith your Cisco 7513 or 7576

10Attach the Cable-Management BracketInstall the HardwareH3120Loosen screws (2)BracketBlowermoduleCard cageStep 1 Locate the twoslotted screws between

11Install Power Supplies in the RouterInstall the Hardware0IOKOKFAILDCFANOUTPUT53427POWERBPOWERACaptive screws0IOKOKFAILACFANOUTPUT0IOKOKFAILACFANOUTP

12Connect AC-Input Power SupplyInstall the Hardware53486Captive screws0IACOKFANOKOUTPUTFAIL0IACOKFANOKOUTPUTFAILPOWERBCable-retention clipWarning The

13Connect DC-Input Power SupplyInstall the Hardwaremovely0IOKOKDCFANOPower leadsattached toterminal block(+) Positive(–) Negative( ) GroundCains

14Step 5 Attach the ground wire to the ground terminals using the 8-mm nut driver.Step 6 Check the power supply’s wiring and color code to verify that

15Connect the RSPConnect the Console PortThesystemconsoleporton the RSP is a DB-25 receptacleDCEport for connecting a data terminal, whichallowsyou to

16Connect the RSPConnect the Console and theAuxiliary Y-CablesThe console and auxiliary Y-cables allow you tosimultaneously connect the console or aux

17Step 1 Check the following components to make sure they are secure:• Each interface processor is inserted all the way into its slot, and captive ins

18Start a Basic ConfigurationStart and Configure the SystemMany privileged-level EXEC commands are used toset operating parameters. To enter theprivileg

19Start and Configure the SystemPerform a Basic ConfigurationUsing SetupNote Therouter’sserial(WAN)cableshouldnotbeconnected to the CSU/DSU unless you a

20Start and Configure the SystemConfigure an Ethernet InterfaceStep 1 To configure your system for an EthernetLAN, respond to the prompts as follows,usin

21Step 2 Determine which protocols you want to allow on the synchronous serial interface and enter theappropriate responses:Configure IP unnumbered on

22Start and Configure the SystemPerform a Basic ConfigurationUsing Configuration ModeAt the reboot, the following example appears:Any interface listed wi

23Install Field Replaceable Units (FRUs)Flash Memory Cards57002SLOT 1NORMALSLOT 0MASTERSLAVESLOT 1NORMALSLOT 0MASTERSLAVEABCSLOT 1NORMALSLOT 0MASTERSL

24Format a Flash Memory CardInstall Field Replaceable Units (FRUs)Flash memory cards shipped as spare parts must beformatted. Use only Intel Series 2+

25Make a Flash Memory Card Image BootableInstall Field Replaceable Units (FRUs)Note In this example, the filename is new.image,and the Flash memory car

26Install Field Replaceable Units (FRUs)Prepare to Remove and Installan RSPTo remove and install an RSP, you will perform thefollowing steps:• Copy th

27Remove and Install an Interface Processor, Filler, VIP, or RSPInstall Field Replaceable Units (FRUs)53376STOP!on contactBottom ejector leverCaptive

1Install the HardwareEJECTSLOT 0SLOT 1NORMALCPU HALTRESETAUX.CONSOLEROUTE SWITCH PROCESSOR 2SLAVEMASTERSLAVE/MASTERENABLEENABLEEJECTSLOT 0SLOT 1NORMAL

28Step 8 If you have a VIP4 and are using HSA with an RSP2 as the slave processor, wait 20-30 seconds, andthen reinsert the RSP2.Install Field Replace

29Install Field Replaceable Units (FRUs)Check the Interface Processoror VIP InstallationNote When a new VIP is inserted or when a VIP ismoved to a new

30Step 5 When the interfaces are up, check the activity of each interface by observing the status LEDs, whichare described in the LED section of your

31Install Field Replaceable Units (FRUs)Copy the Configuration File foran RSPRefer to the appropriate Cisco IOS softwaredocumentation for the configurat

32Install Field Replaceable Units (FRUs)Step 7 Enter the name of the configuration file.The default is to use the name of therouter with thesuffix -confg

33Retrieve the Configuration File for RSPsInstall Field Replaceable Units (FRUs)Retrieve the saved configuration and copy it to NVRAM by accessing the r

34The console display indicates whether or not the operation was successful. A series of exclamation points (!!!!)and [OK] (as shown in the preceding

Remove and Install Port AdaptersInstall Field Replaceable Units (FRUs)

ScrewA

2Prepare to Install the RouterInstall the HardwareNote For detailed hardware installationinstructions and safety guidelines, refer to the Cisco7500 Se

38Note First remove the VIP from the chassis before removing the port adapter from the VIP. See the “Removeand Install an Interface Processor, Filler,

39Remove and Replace the Power SupplyRedundant power supplies support online insertion and removal (OIR); if you remove one power supply, thesecondpow

40For the DC-input power supply: Use a screwdriver to loosen the captive installation screws on theterminal block cover, lift the cover, use the wire

41

78-12954-01Printed in the USA on recycled paper containing 10% postconsumer waste.Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jo

3Install the Router on a Bench or TabletopInstall the HardwarePOWERAPOWERBH3118Note To rack-mount the router, refer to the“Rack-Mount the Router (Reco

4Rack-Mount the Router (Recommended)Install the HardwareH3172 POWERAPOWERB10-32 x 5/8 in. long Phillips pan-head screws with integral square cone wash

5Mount Brackets to the Rack PostsInstall the Hardware53382Rack postFlangeShielded sideNote The distance between the inner edges of theleft and right r

6Secure the SpacersInstall the Hardware53425ABCStep 1 Loosen the 10-32 x 5/8-inch LG Phillipspan-head screw at the end of the ledge ofthe right-side b

7Attach the Chassis EarsInstall the HardwareH3174POWERBPOWERACenter-mount positionFlush-mount positionStep 1 Position the ears on the chassis as follo