Cisco uBR10-LCP2-MC28C Dokumentacja Strona 23
- Strona / 28
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
23
Cisco uBR10-LCP2-MC28C Cable Interface Line Card for the Cisco uBR10012 Router
OL-4653-01
Troubleshooting the Cisco uBR10-LCP2-MC28C Cable Interface Line Card
Tip It is not necessary to configure the cable interface line card if you are installing a replacement card in
the identical slot. The system automatically downloads the necessary configuration information from the
PRE1.
Step 1 Connect all downstream and upstream coaxial cables to the cable interface line card.
Step 2 Configure the cable interface line card if necessary.
For information about configuring the cable interface line card, refer to the Cisco uBR10012 Software
Configuration Guide at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/cable/ubr10k/ubr10012/scg/index.htm
See the release notes at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/cable/ubr10k/ub10krns/index.htm
Troubleshooting the Cisco uBR10-LCP2-MC28C Cable Interface
Line Card
Check the following to help isolate a problem with a card:
Step 1 Are all enabled LEDs on?
If yes, the system is operational.
Step 2 Are any enabled LEDs off?
a. If the enabled LED on a cable interface line card is off, first verify that the card has been enabled
and configured for operations. The enabled LED remains off when a card has not been configured
and enabled.
b. If a port has been enabled but its corresponding enabled LED is still off, check to see if the cable
interface line card has pulled away from the router. Reseat the cable interface line card in its slot
(you do not have to turn off the system power when removing or replacing card). After the system
re-initializes the interfaces, the enabled LED on the cable interface line card should go on.
c. If the enabled LED remains off after the above checks, it is likely that the system has detected a
processor hardware failure. Contact a service representative for instructions.
- Audience 1
- Contents 2
- Cisco uBR10-LCP2 3
- Cisco MC28C 3
- Physical Description 5
- describes the LEDs 6
- Technical Specifications 7
- Waarschuwing 9
- Varoitus 9
- Attention 9
- Avvertenza 10
- Advarsel 10
- ¡Advertencia! 10
- Varning! 11
- Tools and Parts Required 12
- Unpacking and Preparing 12
- Captive 13
- CH OC-12-DSO SM-IR 14
- OL-4653-01 16
- Cisco uBR10-LCP2 Adapter Card 18
- Connecting the Cables 22
- Line Card 23
- Related Documentation 24
- Obtaining Documentation 24
- Documentation CD-ROM 25
- Ordering Documentation 25
- Documentation Feedback 25
- Cisco.com 26
- Technical Assistance Center 26
- Cisco TAC Escalation Center 27
Powiązane produkty i podręczniki dla Networking Cisco uBR10-LCP2-MC28C
(2 strony)
Networking Cisco Cisco ASR 5000 Application Detection and Control Administration Guide Instrukcja Obsługi
(396 strony)
(396 strony)
Networking Cisco AVS 3120 Podręcznik Użytkownika
(14 strony)
(14 strony)
Networking Cisco SN 5428-2 Przewodnik Instalacji
(16 strony)
(16 strony)
Networking Cisco SE2800 Instrukcja Użytkownika
(22 strony)
(22 strony)
Networking Cisco MWR-1900-27 Dokumentacja
(448 strony)
(448 strony)
(4 strony)
Networking Cisco 7513 Dokumentacja
(24 strony)
(24 strony)
Kenwood MFJ-286 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Mikrofony Kenwood MFJ-286.
Dostarczamy 1 pdf podręczników Kenwood MFJ-286 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji