Cisco Fourth-Generation Versatile Interface Processor VIP4 Dokumentacja Pobierz pdf (Strona 62)

4-10

PA-T3+ Serial Port Adapter Installation and Configuration

OL-3505-03

Chapter 4 Configuring the PA-T3+

Configuring the Interfaces

Nonstandard clock rates are rounded (if necessary) to the nearest clock rate that the hardware can

support.

Set a nonstandard clock rate for an interface using the clock rate subcommand. Before you can assign

a nonstandard clock rate, you must use the interface serial command (followed by the interface address

of the interface) to select the interface to which you want to assign the nonstandard clock rate value.

In the following example, a nonstandard clock rate of 1234567 bps is specified:

Router(config-if)# clock rate 1234567

The preceding command example applies to all systems in which the PA-T3+ is supported.

Use the no clock rate command to remove the clock rate.

When you have finished, press Ctrl-Z—hold down the Control key while you press Z—or enter end or

exit to exit configuration mode and return to the EXEC command interpreter prompt. Then write the new

configuration to NVRAM using the copy running-config startup-config command.

The following example shows how to use the show running-config command to determine the exact

clock rate to which the nonstandard clock rate was rounded:

Router# show running-config

Building configuration...

...

interface Serial1/0 (interface Serial3/1/0 on a VIP2)

no ip address

clockrate 1151526

...

In the preceding example, only the relevant output from the show running-config command is shown;

other information is omitted.

Inverting the Clock Signal

Systems that use long cables or cables that are not transmitting the TxC (clock) signal might experience

high error rates when operating at higher transmission speeds. If a PA-T3+ DCE port is reporting a high

number of error packets, a phase shift might be the problem: inverting the clock might correct this phase

shift.

When the EIA/TIA-232 interface is a DTE, the invert-txc command inverts the TxC signal the DTE

receives from the remote DCE. When the EIA/TIA-232 interface is a DCE, the invert-txc command

inverts the clock signal to the remote DTE port. Use the no invert-txc command to change the clock

signal back to its original phase.

Inverting the Data Signal

If you use an EIA/TIA-232 interface on the PA-T3+ port adapter to drive a dedicated T1 line that does

not have B8ZS encoding—a method to avoid 15 zeros—you must invert the data stream

(both TXD and RXD) either in the connecting CSU/DSU or on the interface. To invert the data stream

coming out of the PA-T3+, use the invert data command. By inverting the HDLC data stream, the HDLC

zero insertion algorithm becomes a ones insertion algorithm that satisfies the T1 requirements.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 77 78

Komentarze do niniejszej Instrukcji

Brak uwag

Trust 18953 Scheda Tecnica (1 pagine)

Marchio: Trust | Categoria: Keyboards | Dimensione: 0.84 MB |

Indice

Key features

More information

Più prodotti e manuali per Tastiere Trust

Modelli	Tipo di Documento
19038	Scheda Tecnica Trust 19038, 1 pagine
18915	Scheda Tecnica Trust GXT 280, 1 pagine
18951	Scheda Tecnica Trust 18951, 1 pagine
18805	Scheda Tecnica Trust Gusy Wireless Ultra-thin, 1 pagine
17390	Scheda Tecnica Trust eLight, 1 pagine
18425	Scheda Tecnica Trust Helios, 1 pagine
18801	Scheda Tecnica Trust Gusy, 1 pagine
18770	Scheda Tecnica Trust Nola Wireless Keyboard with mouse, 1 pagine
18423	Scheda Tecnica Trust Helios, 1 pagine
17705	Scheda Tecnica Trust ClassicLine, 1 pagine
18963	Scheda Tecnica Trust Eyso, 1 pagine
18773	Scheda Tecnica Trust Nola, 1 pagine
18486	Scheda Tecnica Trust 18486, 1 pagine
18297	Scheda Tecnica Trust Tacto, 1 pagine
17199	Scheda Tecnica Trust 17199, 1 pagine
18153	Scheda Tecnica Trust Tocamy Wireless Entertain Keyboard, 1 pagine
18422	Scheda Tecnica Trust Helios, 1 pagine
17691	Scheda Tecnica Trust GXT 18 Gaming Keyboard, 1 pagine
17707	Scheda Tecnica Trust GXT 18, 1 pagine
17191	Scheda Tecnica Trust ClassicLine, BE, 1 pagine

Cisco Fourth-Generation Versatile Interface Processor VIP4 Dokumentacja Strona 62

Komentarze do niniejszej Instrukcji

Trust 18953 manuali

Trust 18953 Scheda Tecnica (1 pagine)

Indice

Più prodotti e manuali per Tastiere Trust

Cisco Fourth-Generation Versatile Interface Processor VIP4 Dokumentacja Strona 62

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Cisco Fourth-Generation Versatile Interface Processor VIP4

Trust 18953 manuali

Trust 18953 Scheda Tecnica (1 pagine)

Indice

Più prodotti e manuali per Tastiere Trust