Cisco 3600 - 24 Port Digital Modem Network Module Przewodnik Instalacji Strona 61
- Strona / 142
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Connecting Serial Network Modules to a Network 6-9
4-Port and 8-Port Interface Numbering
To prevent this conflict, Cisco IOS Release 11.2(7)P, which is required to operate 16-port
and 32-port asynchronous network modules, checks when it boots for the presence of
4-port and 8-port asynchronous/synchronous network modules configured as
asynchronous. If if finds any, it rewrites the starting configuration in nonvolatile random
access memory (NVRAM), if necessary, to adopt the new line numbering scheme for these
modules, as shown in Table 6-5.
When an automatic configuration update is performed, the following message appears:
Line number convention changed from 16 lines/slot to 32 lines/slot.
2
1
33–36 33–40
3
1
49–52 49–56
1 Cisco 3640 router only.
Table 6-5 New 4-Port and 8-Port Asynchronous Network Module Interface
Numbering
Slot Number Interface Numbers
(4-Port Module)
Interface Numbers
(8-Port Module)
0 1–4 1–8
1 33–36 33–40
2
1
1 Cisco 3640 router only.
65–68 65–72
3
1
97–100 97–104
Table 6-4 4-Port and 8-Port Asynchronous Network Module Interface
Numbering (continued)
Slot Number Interface Numbers
(4-Port Module)
Interface Numbers
(8-Port Module)
- About This Guide 1
- Audience 2
- Organization 2
- Conventions 4
- Cisco Connection Online 6
- Ordering Documentation 7
- Overview of Cisco Network 9
- Slot Numbering 12
- DO NOT INSTALL WAN INTERFACE 13
- CARDS WITH POWER APPLIED 13
- Unit Numbering 14
- Cisco 2600 Series Routers 15
- Slot and Unit Numbering 17
- Preparing to Install Network 19
- Safety Warnings 20
- Required Tools and Equipment 22
- Installing Network Modules in 23
- Cisco Modular Routers 23
- Asynchronous network module 24
- Blank Network Module Panels 25
- WAN interface card 27
- Connecting Ethernet Network 31
- Connecting Ethernet Ports 32
- AUI Connections 33
- 10BaseT Connections 33
- Ethernet 10BaseT 34
- 10BaseT hub 34
- 10BaseT cable 34
- 1-Port Fast Ethernet Module 35
- 10/100 bTX 37
- FAST ETHERNET 37
- LEDs Enable 37
- Connecting Fast Ethernet PRI 39
- 10/100BaseT 40
- Connecting the PRI Ports 42
- CT1/PRI port (DB-15) 43
- CTRLR 1CTRLR 0 44
- CT1/PRI CSU 45
- • CE1/PRI-B Port on page 5-9 47
- • CE1/PRI-U Port on page 5-11 47
- Connectors) 48
- CE1/PRI-U Port 49
- Fast Ethernet PRI Module LEDs 50
- Connecting Serial Network 53
- Serial DTE or DCE Devices 54
- Signaling Standards Supported 54
- Distance Limitations 55
- Asynchronous Devices 56
- RJ-45 to DB-25 adapter 57
- Modem or terminal 57
- Slot 0Slot 1 Power supply 58
- 1 Cisco 3640 router only 59
- 4-Port Serial Network Module 62
- • V.35 Serial Cable Assembly 63
- • X.21 Serial Cable Assembly 63
- Serial port LEDs 65
- ASYNC 24-31 ASYNC 16-23 66
- ASYNC 8-15 66
- ASYNC 0-7 66
- Network Module 67
- LEDs shown in Table 6-7 70
- Connecting ISDN BRI Network 71
- BRI 3 BRI 2 BRI 1 BRI 0 73
- B1 B2 B1 B2 B1 B2 B1 B2 73
- BRI S/T Module LEDs 74
- BRI U ports (RJ-45) 76
- NT1 LEDs 77
- ISDN BRI LEDs 77
- BRI U Modules LEDs 78
- Connecting ISDN PRI Network 81
- CT1/PRI-U port (DB-15) 82
- CT1/PRI-U ports (DB-15) 83
- CT1/PRI Module LEDs 84
- Network Modules 85
- CT1/PRI CSU Module LEDs 87
- Table 8-2 88
- (120-ohm) Network Modules 89
- (DB-15-to-DB-15 Connectors) 91
- 1FE-1CE1-B/U 92
- CE1/PRI Module LEDs 93
- (75-ohm) Network Modules 94
- CSU with BNC connectors 95
- Connecting Voice Network 99
- Voice Network Module LEDs 101
- Connecting Digital 103
- Modem Network Modules to a 103
- Hardware Requirements 105
- Interface Numbering 106
- Figure 10-3.) 108
- Alignment holes 109
- Connector edge 109
- Removing 6-Port MICA Modules 111
- Digital Modem Module LEDs 118
- Connecting Analog Modem 119
- Network Modules to a Network 119
- 76543210 120
- 15 14 13 12 11 10 9 8 120
- Supported Network Protocols 121
- RJ-11 jack 124
- Analog modem port (RJ-11) 124
- Straight-through 124
- RJ-11 cable 124
- 76543210IN USE 125
- 15 14 13 12 11 10 9 8 IN USE 125
- Connecting ATM Network 127
- Modules to a Network 127
- RJ-45 port 128
- Enable LED 128
- ATM traffic 128
- ADSL modem 129
- RJ-45-to-RJ-45 cable 129
- ATM-25 port 129
- ATM-25 Network Module LEDs 130
- Connecting HSSI Network 131
- HSSI port LEDs 132
- HSSI port 132
- External DSU 133
- HSSI DTE cable 133
- HIGH SPEED SERIAL 133
- HSSI Network Module LEDs 134
- Connecting Compression 137
- Supported Interfaces 138
- COMPRESSION 139
- Error LED 139
- Active LED 139
- FCC Class B Compliance 141
Powiązane produkty i podręczniki dla Networking Cisco 3600 - 24 Port Digital Modem Network Module
(44 strony)
Networking Cisco WS-C2960-8TC-L Dokumentacja
(19 strony)
(19 strony)
Networking Cisco 1900 series Dokumentacja
(44 strony)
(44 strony)
Networking Cisco 40-Gigabit and 100-Gigabit CFP Transceiver Modules Instrukcja Użytkownika
(8 strony)
(8 strony)
Networking Cisco EPC3208 Instrukcja Użytkownika
(98 strony)
(98 strony)
Networking Cisco CX-TRIP2 Dokumentacja
(28 strony)
(28 strony)
(48 strony)
Networking Cisco 3631 Dokumentacja
(198 strony)
(198 strony)
Networking Cisco 2650 - 2650 Router Dokumentacja
(266 strony)
(266 strony)
Clear-Com Türsprechanlagen Benutzerhandbücher
Beginnend mit T
Komentarze do niniejszej Instrukcji