Cisco 2650 - 2650 Router Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Networking Cisco 2650 - 2650 Router. How to Configure Cisco 2600 Routers Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 15
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
Helsinki University of Technology
Department of Communications and Networking
How to Configure Cisco 2600 Routers
Juha Järvinen 10.6.2004
Juha.Jarvinen@netlab.hut.fi
Modified by Zhong Yunqiu 7.8.2008
Przeglądanie stron 0
1 2 3 4 5 6 ... 14 15

Podsumowanie treści

Strona 1

Helsinki University of Technology Department of Communications and Networking How to Configure Cisco 2600 Routers

Strona 2 - Table of Contents

10 • area OSPF area parameters • auto-cost Calculate OSPF interface cost according to bandwidth • capabilit

Strona 3 - Purpose

11 If no OSPF router ID is explicitly configured, OSPF computes the router-ID based on the items 2, 3, and 4 and restarts OSPF (if the process is

Strona 4

12 ip ospf transmit-delay seconds Set the estimated number of seconds it takes to transmit a link state update packet on an OSPF interface. ip ospf

Strona 5 - 1.1.4 No Form

13 2.3 RIP and OSPF Redistribution 2.3.1 RIP If you like to redistribute routing information to OSPF, you have to tell RIP running router process-

Strona 6 - 1.3 Configuration Files

14 3 Configure CEF Load balancing is based on a combination of source and destination packet information; it allows you to optimize resources

Strona 7 - Router#config terminal

15 References [1] Cisco: Configuring RIP http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/np1_c/1cprt1/1crip.pdf [2] Cisco: C

Strona 8 - 2.1.2 Specify a RIP Version

2 Table of Contents Purpose ...

Strona 9 - 2.2.1 OSPF Commands

3 Purpose Purpose of this document is to show how to use and configure Cisco 2600 Series routers. Mainly this document has been done f

Strona 10 - 2.2.2 Router ID

4 1 Cisco Inter-network Operating System (IOS) 1.1 Cisco IOS Operation Modes The Cisco Software provides access to four different command modes. T

Strona 11 - 2.2.3 Virtual Link

5 Router#Router>Router(config)#Router(config-if)#enableconfigureterminalinterface etc.exitexit, end, Ctrl-Zdisableexit, end, Ctrl-Z Figure 1. Fou

Strona 12 - 2.2.6 No Form

6 routing is enabled by default. To disable IP routing, enter the no ip routing command and enter ip routing to re-enable it. 1.2 Getting Help In a

Strona 13 - 2.3.4 LAN

7 1.4 Configuration System (Setup) In privileged EXEC mode you can setup the whole system, for example setup network cards, put IP addresses, start

Strona 14 - 3 Configure CEF

8 2 Routing Protocol Configuration 2.1 Routing Information Protocol RIP You can modify RIP routing by giving the next command in global

Strona 15 - References

9 Table 2. RIP version commands in sending. Command Purpose ip rip send version 1 Configure an interface to send only RIP version 1 packets.

Komentarze do niniejszej Instrukcji

Brak uwag