Cisco AIR-ANT2544V4M-R Dokumentacja

GETTING STARTED GUIDE Cisco Aironet 2600 Series Access PointsJuly, 2012P/N: 78-20842-011 About this Guide2 Introduction to the Access Point3 Safety I

10 Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space.Note Make sure that the co

11 Preparing the Access PointBefore you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool

12 Performing a Pre-Installation ConfigurationThe following procedures ensure that your access point installation and initial operation go as expected

13 Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco WCS proce

14 Note The 2600 series access point requires a Gigibit Ethernet link to prevent the Ethernet port from becoming a bottleneck for traffic because wire

15 8 Mounting the Access PointCisco Aironet 2600 series access points can be mounted in several configurations, including on a suspended ceiling, on

16 10 TroubleshootingIf you experience difficulty getting your access point installed and running, look for a solution to your problem in this guide

17 Figure 5 Access Point LED LocationThe access point status LED indicates various conditions and are described in Table 1.1Status LEDTable 1 LED Stat

18 Troubleshooting the Access Point Join ProcessAccess points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-

19 Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server. You do not need to enable any

2 1 About this GuideThis Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series Access Point. The 2600 Series Acc

20 • The access point is still connected to the same controller, and a specific syslog server IP address has been configured for the access point on t

21 Manufacturer:Cisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAThis device complies with Part 15 rules. Operation is subject to the

22 Caution Within the 5.15 to 5.25 GHz and 5.47-5.725 GHz bands, this device is restricted to indoor operations to reduce any potential for harmful in

23 Guidelines for Operating Cisco Aironet Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco Airone

24 Statement 371—Power Cable and AC AdapterEnglish TranslationWhen installing the product, please use the provided or designated connection cables/pow

25 This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harm

26 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC

27 The following standards were applied:EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1Health & Safety—EN60950-1: 2005; EN 50385: 2002Radio—EN 300 3

28 This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC.Note This equipment is intended to be used in all EU a

29 As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a lo

3 –Management Frame Protection (MFP)–Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps data-rates• 32 MB fla

30 This Device Meets the Industry Canada Guidelines for Exposure to Radio WavesThe 2600 series device includes a radio transmitter and receiver. It is

31 • United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk • Cellular Telecommunications Association at this URL: www.wo

32 English TranslationAdministrative Rules for Low-power Radio-Frequency DevicesArticle 12For those low-power radio-frequency devices that have alread

33 English TranslationLow-power Radio-frequency Devices Technical SpecificationsOperation of Cisco Aironet Access Points in BrazilThis section contain

CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, andLearn is a serv

35 dns-server <DNS Server> Where:<pool name> is the name of the DHCP pool, such as AP2602<IP Network> is the network IP address wher

36 Operating temperatures AP2602E: -4 to 131 degrees F (-20 to 55 degrees C)AP2602I: 32 to 104 degrees F (0 to 40 degrees C)Storage temperature –22 to

37 14 Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering

38

39

4 WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074WarningThis product relies on the building’

40 CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a

5 4 UnpackingTo unpack the access point, follow these steps:Step 1 Unpack and remove the access point and the accessory kit from the shipping box.Ste

6 These antennas are supported on the 2602E:Internal AntennasThe 2602I model access points are configured with up to four dual-band inverted-F antenna

7 6 Access Point Ports and ConnectorsThe 2602E model access points have external antenna connectors and the LED indictor on the top of the model, as

8 Figure 2 Access Point LED Indicator (top)The ports and connections on the bottom of the access point are shown in Figure 3.Figure 3 Access Point Por

9 7 Configuring the Access PointThis section describes how to connect the access point to a wireless LAN controller. Because the configuration proces